InverterWorks Request a quote

Guide

MPPT vs PWM: what the difference actually costs

The two controllers do the same job and differ in one thing: what happens to the array voltage. That single difference decides whether you throw away a quarter of your panels' output — or none of it.

PV array 200–500 V DC Battery 48 V nominal House 120 / 230 V AC Grid or genset MPPT DC → AC Transfer relay 1 2 3 4 5

Anatomy

Five connections decide which model fits. Ask for the datasheet to confirm each one on the exact rating you are buying.

  1. 1PV DC inputString voltage window and max input current per tracker.
  2. 2MPPT trackerOne tracker per roof orientation; two trackers help a partly shaded array.
  3. 3Battery portNominal voltage and chemistry must match the bank you already own.
  4. 4AC outputContinuous and surge rating, and whether the backup panel is separate.
  5. 5Grid or genset inputGrid-code approval for your country, plus generator start support.

The difference is what happens to the array voltage

A solar panel produces power at its maximum power point, which for a nominal 12 V panel is around 17–18 V. A battery, at 50% state of charge, sits near 12.2 V and rises to 13.5–14.4 V while charging.

A PWM controller connects the array to the battery directly, so the array is forced down to battery voltage. The current is roughly preserved, the voltage is not, and the difference is dissipated as heat. A MPPT controller runs the array at its own maximum power point and converts the higher voltage down to battery voltage, keeping most of the power.

The efficiency math

Take a 200 W panel with Vmp 18 V and Imp 11.1 A feeding a 12 V bank held at 13.5 V:

  • PWM: the array is clamped to 13.5 V, so about 13.5 × 11.1 ≈ 150 W reach the battery — roughly 75% of nameplate.
  • MPPT: conversion is 95–99%, so about 190 W reach the battery.

The gap widens with panel voltage. A 60-cell panel with Vmp around 30 V on a 12 V bank loses about half its output through a PWM controller, which is why those two are rarely paired. It narrows to almost nothing when the panel is a 12 V type and the bank is 12 V — the case PWM was designed for.

When PWM is still the right buy

  • Array under roughly 200–300 W: a trickle charger, a gate opener, one panel on a shed.
  • A panel whose Vmp is already close to the bank voltage.
  • A cost-sensitive cabin where the price gap is a meaningful share of the whole system.
  • Anywhere simplicity matters more than yield: fewer parts, no inductor, nothing to configure.

PWM is also more forgiving of a small panel and a big battery, which is why it survives in maintenance and standby applications.

When MPPT pays for itself

  • Wiring series strings. Two or three panels in series give 60–100 V, which PWM simply cannot use.
  • Long cable runs. Higher array voltage means lower current and less line loss before the controller even starts.
  • Cold climates. Panel voltage rises as temperature falls; MPPT keeps tracking, PWM keeps discarding.
  • Arrays above 300 W. Recovering 20–25% of a 1 kW array usually pays back the price difference within a season or two.

Sizing the controller

Charge current is array watts divided by bank volts, derated: 800 W into a 24 V bank gives about 33 A nominal, derated to about 27 A, so buy a 30 A controller. Then check two limits: the controller's maximum PV input voltage against array Voc in the coldest expected temperature (about 1.15–1.2× the 25 °C figure), and its temperature derating — most controllers must be derated above 40 °C ambient, which is exactly the inside of a cabinet in summer.

Five mistakes that cost real yield

  1. Sizing on nameplate watts and forgetting the 0.8 derate.
  2. Ignoring Voc headroom: a string that is fine at 25 °C can exceed the input limit on a cold morning.
  3. Mounting the controller in a sealed box with no airflow.
  4. Mixing orientations in one string under a single tracker.
  5. Running two controllers on one bank without a shared voltage sense, so each thinks it is in charge.

Get the controller right and the rest of the chain behaves; get it wrong and no inverter specification can recover the lost hours.

FAQ

Common questions

Is MPPT always better than PWM?

No. Below roughly 200–300 W, with a panel whose Vmp is already close to battery voltage, the extra yield of MPPT is small and the price gap is not recovered. Above that, or whenever the array runs at a higher voltage than the bank, MPPT wins clearly.

How much power does PWM actually waste?

It clamps the array to battery voltage, so any voltage above that is lost. A 12 V nominal panel with Vmp around 18 V feeding a bank at 13.5 V delivers roughly 75% of nameplate. A 24 V panel on a 12 V bank delivers closer to 50–60%.

How do I size the charge controller?

Take array watts divided by bank volts, then derate by about 0.8 for real conditions and round up to the next standard size: 800 W into a 24 V bank is about 27 A, so a 30 A controller. Also check the controller's maximum PV input voltage against the array Voc in the coldest expected temperature, not at 25 °C.

Can I mix panel orientations on one MPPT controller?

Only if the controller has independent inputs or you use one controller per string. Panels facing different directions have different maximum power points, and a single tracker settles on a compromise that costs more than the second controller.

Sourcing

Need the current datasheet?

Tell us array watts, panel Vmp and Voc, and bank voltage. We reply with the controller type and rating that fits, with datasheet and lead time.

Request a quote