A solar inverter does one essential job: it turns the direct current (DC) produced by solar panels into alternating current (AC) that a house, a workshop or a grid can use. Everything else it does — tracking the best operating point, charging a battery, protecting line workers — follows from that job.
The problem in one paragraph
A panel is a current source, not a voltage source. Its output changes with light and temperature, and for any given condition there is one operating point where the panel delivers the most power. A house needs 120/240 V AC at a fixed 50 or 60 Hz. Between the panel and the socket, three things must happen: the array must be held at its best operating point, the DC must be switched into a clean sine wave, and everything must stay synchronised with the grid while remaining safe if the grid disappears.
Step 1: maximum power point tracking (MPPT)
An MPPT tracker is a DC-DC converter that adjusts the voltage the array sees, hunting for the point where volts × amps is highest. On a partly cloudy day that point moves constantly, and a tracker re-finds it many times per second. This is why an inverter with a good tracker can beat a larger array with a poor one: the panels are not producing what their label says, and the tracker decides how much of the available power is actually collected.
Most residential inverters have one to three trackers, each serving its own string. Panels on one tracker should share orientation and shade; otherwise the tracker averages two mismatched power curves and loses on both.
Step 2: DC to AC, the switching stage
Inside the inverter, power semiconductors switch the DC on and off thousands of times a second, building a stepped waveform that is filtered into a sine wave. How that switching is done defines the price and the losses:
- High-frequency designs switch fast through a small transformer, which makes them light and cheap, with efficiency in the mid-to-high 90s percent.
- Low-frequency designs use a large iron transformer running at 50/60 Hz. They are heavy and less efficient at light load, but they tolerate surge and heat, which is why off-grid units for pumps are usually built this way.
- Transformerless designs skip the transformer in the grid path entirely, giving the highest efficiency, at the cost of stricter DC-side safety requirements.
The output is a sine wave, and the total harmonic distortion figure on the datasheet (commonly below 3%) says how close to a clean sine the electronics get. Motors and audio equipment care about that number; a phone charger does not.
Step 3: synchronising to the grid, or not
A grid-tie inverter samples the grid voltage and frequency and pushes current in phase with it. If the grid drifts outside a window — voltage, frequency, or a sudden loss — the unit must disconnect within a specified time. That is anti-islanding protection, and it exists so a line worker repairing the street does not meet a live cable fed by your roof.
An off-grid inverter does the opposite: it creates its own voltage and frequency reference, and there is nothing to synchronise to. A hybrid does both, opening a relay to the grid when the grid fails and forming its own reference for the backup output.
Step 4: what happens to the energy
With no battery, the inverter sends energy to the house first and exports the rest, or limits export to zero where the utility requires it. With a battery, it chooses between charging, discharging and exporting, usually on a self-consumption priority. That control logic is what people mean by "smart" — and it is also where cheap firmware disappoints: an inverter that charges the battery from the grid at peak tariff, or refuses to discharge on a cloudy evening, is doing the switching correctly and the logic badly.
The losses you pay for
Peak efficiency of 97–98% is measured at an ideal load. Across a real day, the European or CEC weighted efficiency is the honest number, commonly 95–97%. Add battery round-trip losses of roughly 5–10% on a lithium system, idle draw of 20–60 W running 24 hours, and the gap between the panel label and the socket becomes concrete.
Reading a datasheet afterwards
Once the mechanism is clear, a datasheet stops being a wall of numbers. Check four of them in order: the MPPT voltage window, the maximum input current per tracker, the rated output at the ambient temperature on site, and the surge rating. Those four decide whether a given inverter can do the job you are buying it for.